                                   
|
|
|
| 生产单位： |
一车间 |
|
|
|
| K157FM（大长江）左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
|
|
|
|
|
|
|
| 镗孔 |
21 |
41.18% |
41.18% |
|
|
|
|
|
|
|
|
|
|
| 精磨 |
13 |
66.67% |
25.49% |
|
|
|
|
|
|
|
|
|
|
| 铣键槽 |
5 |
76.47% |
9.80% |
|
|
|
|
|
|
|
|
|
|
| U钻 |
4 |
84.31% |
7.84% |
|
|
|
|
|
|
|
|
|
|
| 其它 |
3 |
90.20% |
5.88% |
|
|
|
|
|
|
|
|
|
|
| 插齿 |
2 |
94.12% |
3.92% |
|
|
|
|
|
|
|
|
|
|
| 磨锥 |
2 |
98.04% |
3.92% |
|
|
|
|
|
|
|
|
|
|
| 精车 |
1 |
100.00% |
1.96% |
|
|
|
|
|
|
|
|
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 钻工艺孔 |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 校正 |
|
100.00% |
0.00% |
|
|
|
|
|
|
|
|
|
|
| 综合 |
51 |
|
|
|
|
|
|
|
|
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
一车间 |
|
|
|
| K157FM（大长江） 右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 钻深孔 |
9 |
32.14% |
32.14% |
|
|
| 镗孔 |
6 |
53.57% |
21.43% |
|
|
| 精磨 |
5 |
71.43% |
17.86% |
|
|
| 铣键槽 |
3 |
82.14% |
10.71% |
|
|
| 滚螺纹 |
2 |
89.29% |
7.14% |
|
|
| 钻斜孔 |
2 |
96.43% |
7.14% |
|
|
| U钻 |
1 |
100.00% |
3.57% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 钻工艺孔 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 校正 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
28 |
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| AX100
左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
12 |
75.00% |
75.00% |
|
|
| 镗孔 |
2 |
87.50% |
12.50% |
|
|
| 钻销孔 |
1 |
93.75% |
6.25% |
|
|
| 铣半圆键 |
1 |
100.00% |
6.25% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 数控磨 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
16 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| AX100
右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
30 |
100.00% |
100.00% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 钻销孔 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 铣半圆键 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 数控磨 |
|
100.00% |
0.00% |
|
|
| 镗孔 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
30 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| 847026左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
14 |
63.64% |
63.64% |
|
|
| 数控磨 |
4 |
81.82% |
18.18% |
|
|
| 镗孔 |
3 |
95.45% |
13.64% |
|
|
| 车孔 |
1 |
100.00% |
4.55% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 钻销孔 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 铣半圆键 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
22 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| 847026右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
16 |
64.00% |
64.00% |
|
|
| 数控磨 |
5 |
84.00% |
20.00% |
|
|
| 铣半圆键 |
2 |
92.00% |
8.00% |
|
|
| 精车 |
1 |
96.00% |
4.00% |
|
|
| 镗孔 |
1 |
100.00% |
4.00% |
|
|
| 钻销孔 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
25 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| 848776/848773左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
29 |
58.00% |
58.00% |
|
|
| 镗孔 |
10 |
78.00% |
20.00% |
|
|
| 滚螺纹 |
6 |
90.00% |
12.00% |
|
|
| 精车 |
2 |
94.00% |
4.00% |
|
|
| 车孔 |
1 |
96.00% |
2.00% |
|
|
| 数控磨 |
1 |
98.00% |
2.00% |
|
|
| 精车R |
1 |
100.00% |
2.00% |
|
|
| 钻销孔 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 铣半圆键 |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
50 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
二车间 |
|
|
|
|
| 848776/848773右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
39 |
55.71% |
55.71% |
|
|
| 数控磨 |
15 |
77.14% |
21.43% |
|
|
| 铣半圆键 |
11 |
92.86% |
15.71% |
|
|
| 镗孔 |
3 |
97.14% |
4.29% |
|
|
| 钻销孔 |
2 |
100.00% |
2.86% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
70 |
|
280.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
三车间 |
|
|
|
|
| SC4160479左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 精磨 |
39 |
19.12% |
19.12% |
|
|
| 铣键 |
30 |
33.82% |
14.71% |
|
|
| 磨孔 |
25 |
46.08% |
12.25% |
|
|
| 车孔 |
24 |
57.84% |
11.76% |
|
|
| 车R |
18 |
66.67% |
8.82% |
|
|
| 滚螺纹 |
17 |
75.00% |
8.33% |
|
|
| 磨底径 |
15 |
82.35% |
7.35% |
|
|
| 校正 |
12 |
88.24% |
5.88% |
|
|
| 精车 |
11 |
93.63% |
5.39% |
|
|
| 钻销孔 |
6 |
96.57% |
2.94% |
|
|
| 其它 |
5 |
99.02% |
2.45% |
|
|
| 压合 |
2 |
100.00% |
0.98% |
|
|
| 综合 |
204 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
三车间 |
|
|
|
|
| 4191248左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 精磨 |
12 |
33.33% |
33.33% |
|
|
| 校正 |
12 |
66.67% |
33.33% |
|
|
| 磨孔 |
8 |
88.89% |
22.22% |
|
|
| 车孔 |
3 |
97.22% |
8.33% |
|
|
| 精车 |
1 |
100.00% |
2.78% |
|
|
| 车R |
|
100.00% |
0.00% |
|
|
| 磨底径 |
|
100.00% |
0.00% |
|
|
| 滚螺纹 |
|
100.00% |
0.00% |
|
|
| 磨R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
36 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
三车间 |
|
|
|
|
| 4191248右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 精磨 |
6 |
37.50% |
37.50% |
|
|
| 铣键 |
4 |
62.50% |
25.00% |
|
|
| 磨孔 |
4 |
87.50% |
25.00% |
|
|
| 滚螺纹 |
1 |
93.75% |
6.25% |
|
|
| 校正 |
1 |
100.00% |
6.25% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 磨底径 |
|
100.00% |
0.00% |
|
|
| 磨R |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
16 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
五车间 |
|
|
|
|
| 12F6连杆 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 磨小孔 |
97 |
44.09% |
44.09% |
|
|
| 珩小孔 |
43 |
63.64% |
19.55% |
|
|
| 磨大孔 |
40 |
81.82% |
18.18% |
|
|
| 珩大孔 |
40 |
100.00% |
18.18% |
|
|
| 磨平面 |
|
100.00% |
0.00% |
|
|
| 钻油孔 |
|
100.00% |
0.00% |
|
|
| 钻小孔 |
|
100.00% |
0.00% |
|
|
| 钻大孔 |
|
100.00% |
0.00% |
|
|
| 车小孔 |
|
100.00% |
0.00% |
|
|
| 车大孔 |
|
100.00% |
0.00% |
|
|
| 校直 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
220 |
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
五车间 |
|
|
|
|
| 157FM连杆 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 磨小孔 |
60 |
35.71% |
35.71% |
|
|
| 珩小孔 |
44 |
61.90% |
26.19% |
|
|
| 珩大孔 |
43 |
87.50% |
25.60% |
|
|
| 磨大孔 |
21 |
100.00% |
12.50% |
|
|
| 磨平面 |
|
100.00% |
0.00% |
|
|
| 钻油孔 |
|
100.00% |
0.00% |
|
|
| 钻小孔 |
|
100.00% |
0.00% |
|
|
| 钻大孔 |
|
100.00% |
0.00% |
|
|
| 车小孔 |
|
100.00% |
0.00% |
|
|
| 车大孔 |
|
100.00% |
0.00% |
|
|
| 校直 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
168 |
|
100.00% |
|
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
五车间 |
|
|
|
|
| GFC系列 |
|
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
| 珩小孔 |
84 |
61.31% |
61.31% |
|
|
| 磨大孔 |
21 |
76.64% |
15.33% |
|
|
| 磨小孔 |
18 |
89.78% |
13.14% |
|
|
| 珩大孔 |
14 |
100.00% |
10.22% |
|
|
| 磨平面 |
|
100.00% |
0.00% |
|
|
| 钻油孔 |
|
100.00% |
0.00% |
|
|
| 钻小孔 |
|
100.00% |
0.00% |
|
|
| 钻大孔 |
|
100.00% |
0.00% |
|
|
| 车小孔 |
|
100.00% |
0.00% |
|
|
| 车大孔 |
|
100.00% |
0.00% |
|
|
| 校直 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
137 |
|
100.00% |
|
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
五车间 |
|
|
|
|
| 8861200001连杆 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 磨大孔 |
46 |
39.66% |
39.66% |
|
|
| 磨小孔 |
39 |
73.28% |
33.62% |
|
|
| 珩小孔 |
22 |
92.24% |
18.97% |
|
|
| 珩大孔 |
7 |
98.28% |
6.03% |
|
|
| 磨平面 |
2 |
100.00% |
1.72% |
|
|
| 钻油孔 |
|
100.00% |
0.00% |
|
|
| 钻小孔 |
|
100.00% |
0.00% |
|
|
| 钻大孔 |
|
100.00% |
0.00% |
|
|
| 车小孔 |
|
100.00% |
0.00% |
|
|
| 车大孔 |
|
100.00% |
0.00% |
|
|
| 校直 |
|
100.00% |
0.00% |
|
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
116 |
|
100.00% |
|
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
五车间 |
|
|
|
|
| 847026连杆 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 珩小孔 |
19 |
61.29% |
61.29% |
|
|
| 其它 |
4 |
74.19% |
12.90% |
|
|
| 磨大孔 |
3 |
83.87% |
9.68% |
|
|
| 磨平面 |
2 |
90.32% |
6.45% |
|
|
| 钻大孔 |
2 |
96.77% |
6.45% |
|
|
| 磨小孔 |
1 |
100.00% |
3.23% |
|
|
| 钻油孔 |
|
100.00% |
0.00% |
|
|
| 钻小孔 |
|
100.00% |
0.00% |
|
|
| 车小孔 |
|
100.00% |
0.00% |
|
|
| 车大孔 |
|
100.00% |
0.00% |
|
|
| 珩大孔 |
|
100.00% |
0.00% |
|
|
|
| 校直 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
31 |
|
100.00% |
|
|
|
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
六车间 |
|
|
|
|
| 8012轴 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 精磨 |
14 |
31.82% |
31.82% |
|
|
| 钻φ16.5孔 |
7 |
47.73% |
15.91% |
|
|
| 粗磨 |
6 |
61.36% |
13.64% |
|
|
| 钻φ3.8孔 |
3 |
68.18% |
6.82% |
|
|
| 铣扁 |
3 |
75.00% |
6.82% |
|
|
| 其它 |
3 |
81.82% |
6.82% |
|
|
| 车φ16.5孔 |
2 |
86.36% |
4.55% |
|
|
| 枪钻 |
2 |
90.91% |
4.55% |
|
|
| 镗孔 |
2 |
95.45% |
4.55% |
|
|
| 钻φ1、φ2孔 |
1 |
97.73% |
2.27% |
|
|
| 磨偏心 |
1 |
100.00% |
2.27% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 铰φ3.8孔 |
|
100.00% |
0.00% |
|
|
| 精车偏心 |
|
100.00% |
0.00% |
|
|
| 综合 |
44 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
九车间 |
|
|
|
| 157FM 左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 镗孔 |
32 |
29.09% |
29.09% |
|
|
| 精磨 |
24 |
50.91% |
21.82% |
|
|
| 铣键槽 |
22 |
70.91% |
20.00% |
|
|
| 精车R |
15 |
84.55% |
13.64% |
|
|
| 钻扩攻螺纹 |
11 |
94.55% |
10.00% |
|
|
| 精车 |
3 |
97.27% |
2.73% |
|
|
| U钻 |
3 |
100.00% |
2.73% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
110 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
九车间 |
|
|
|
| 157FM 右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 精磨、空刀 |
15 |
29.41% |
29.41% |
|
|
| 镗孔 |
15 |
58.82% |
29.41% |
|
|
| U钻 |
8 |
74.51% |
15.69% |
|
|
| 精车 |
6 |
86.27% |
11.76% |
|
|
| 滚螺纹、键 |
6 |
98.04% |
11.76% |
|
|
| 精车R |
1 |
100.00% |
1.96% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 钻斜孔 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
51 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
| 生产单位： |
十一车间 |
|
|
|
|
| GY6+HA1左曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
|
| 数控磨 |
9 |
29.03% |
29.03% |
|
|
|
| 滚螺纹 |
8 |
54.84% |
25.81% |
|
|
|
| 校正 |
7 |
77.42% |
22.58% |
|
|
|
| 镗孔 |
4 |
90.32% |
12.90% |
|
|
|
| 精车 |
3 |
100.00% |
9.68% |
|
|
|
| U钻 |
|
100.00% |
0.00% |
|
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
|
| 滚键 |
|
100.00% |
0.00% |
|
|
|
| 精车R |
|
100.00% |
0.00% |
|
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
31 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
十一车间 |
|
|
|
|
| GY6+HA1右曲柄 |
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 数控磨 |
16 |
29.63% |
29.63% |
|
|
| 滚螺纹 |
12 |
51.85% |
22.22% |
|
|
| 校正 |
10 |
70.37% |
18.52% |
|
|
| U钻 |
7 |
83.33% |
12.96% |
|
|
| 精车 |
5 |
92.59% |
9.26% |
|
|
| 镗孔 |
2 |
96.30% |
3.70% |
|
|
| 铣半圆键 |
1 |
98.15% |
1.85% |
|
|
| 精车R |
1 |
100.00% |
1.85% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其它 |
|
100.00% |
0.00% |
|
|
| 综合 |
54 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
| 生产单位： |
十一车间 |
|
|
|
|
| GFC 左曲柄 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
|
| 校正 |
12 |
60.00% |
60.00% |
|
|
|
| 滚螺纹 |
4 |
80.00% |
20.00% |
|
|
|
| U钻 |
2 |
90.00% |
10.00% |
|
|
|
| 滚花键 |
2 |
100.00% |
10.00% |
|
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
|
| 车孔 |
|
100.00% |
0.00% |
|
|
|
| 数控磨 |
|
100.00% |
0.00% |
|
|
|
| 镗孔 |
|
100.00% |
0.00% |
|
|
|
| 精磨R |
|
100.00% |
0.00% |
|
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
|
| 其他 |
|
100.00% |
0.00% |
|
|
|
| 综合 |
20 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 生产单位： |
十一车间 |
|
|
|
|
|
| GFC右曲柄 |
|
|
|
|
| 工序名称 |
废品数 |
累积废品率 |
废品率 |
|
|
|
| 校正 |
12 |
52.17% |
52.17% |
|
|
| 铣半圆键 |
4 |
69.57% |
17.39% |
|
|
| U钻 |
3 |
82.61% |
13.04% |
|
|
| 数控磨 |
3 |
95.65% |
13.04% |
|
|
| 滚螺纹 |
1 |
100.00% |
4.35% |
|
|
| 精车 |
|
100.00% |
0.00% |
|
|
| 粗车R |
|
100.00% |
0.00% |
|
|
| 镗孔 |
|
100.00% |
0.00% |
|
|
| 精磨R |
|
100.00% |
0.00% |
|
|
| 车凹 |
|
100.00% |
0.00% |
|
|
| 压合 |
|
100.00% |
0.00% |
|
|
| 其他 |
|
100.00% |
0.00% |
|
|
| 综合 |
23 |
|
100.00% |
|
|
|
编制： |
王瑞花 |
|
审核： |
李先玉 |
|
批准： |
金山木 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|